Mobile Header below

We Don't Make Ladders. We Make Ladders

LadderPort™, the inexpensive permanent building mounted extension ladder receiver, securely holds the
ladder in place. Hooks secure the ladder while side plates prevent it from moving left or right. The solid metal
grab bars enable the technician to climb up and down a portable extension ladder comfortably and safely.

The benefits of LadderPort™ include:

  • Meets OSHA Regulation 1926.1053(b)(1)
  • Eliminates fear of climbing on and off the roof
  • Safe and reliable – even in ice and snow
  • Keeps contractors from tramping through your building with materials to reach an interior roof hatch
  • Different models available to protect gutters and building exterior
  • Eliminates vandals and children from using permanently mounted ladders
  • Reduces liability & lowers the risk of being sued due to a fall
  • Made in the USA

why choose LadderPort™?

LadderPort™ is the inexpensive permanent building mounted extension ladder receiver, securely holds the
ladder in place. Hooks secure the ladder while side plates prevent it from moving left or right. The solid metal
grab bars enable the technician to climb up and down a portable extension ladder comfortably and safely

LadderPort™ Type 1* – Standard Flush Mount

First choice in comfortable safety when the building has a flat, strong wall and a simple flashing detail. This model accommodates a fascia board to 6″ below the top of the roof edge flashing.

  • Designed for Use on a Flat Wall
  • LadderPort™ shall be of welded steel construction
  • Powder coated for lasting durability, available in safety yellow and dark brown
  • Hand stops on top of handrails shall be included
  • Grab rails shall meet OSHA requirements for height and clearance
  • LadderPort™ shall be mounted to building in an architect approved manner utilizing ½” steel threaded rod with back plates or other architect approved fastening system
LadderPort™ Type 2* – Gutter Saver

Protect your gutters from the harm of an extension ladder. Use this model when a gutter up to 8″ wide by 8″ tall is present. This model must be attached to a strong wall.

  • Designed to Provide Clearance for Commercial Gutters up to 8"x8"
  • LadderPort™ shall be of welded steel construction
  • Powder coated for lasting durability, available in safety yellow and dark brown
  • Hand stops on top of handrails shall be included
  • Grab rails shall meet OSHA requirements for height and clearance
  • LadderPort™ shall be mounted to building in an architect approved manner utilizing ½” steel threaded rod with back plates or other architect approved fastening system
LadderPort™ Type 3* – Adjustable

Select this model when the wall has crown or decorative detail at top flashing. Its telescoping lower attach points easily adjust & attach to a strong wall, such as masonry (block/brick), providing a stable unit. Drill bit & ss steel hardware. Included for adjusting the telescoping lower attach points.

  • Designed for Use with Cornice Detail
  • LadderPort™ shall be of welded steel construction
  • Powder coated for lasting durability, available in safety yellow and dark brown
  • Hand stops on top of handrails shall be included.
  • Grab rails shall meet OSHA requirements for height and clearance
  • Shall be securely fastened to wood nailer or other suitable structural member at top of cornice and shall also be set level and lower mounting stand offs shall be cut and drilled in accordance with included instructions for proper length
  • Bottom support shall be securely fastened to masonry construction utilizing ½” steel threaded rod and back plates or other architect approved fastening system
LadderPort™ Type 4* – PreFab Metal Bldgs

Meets the requirements of pre-engineered metal buildings with its adjustable attach points at bottom & top legs. Use where there is no easy method of attaching to the roofline. Bolting to a 3” X 3” angle frame secured to the girth inside the building recommended.

  • Designed for Use on a Flat Wall
  • LadderPort™ shall be of welded steel construction
  • Powder coated for lasting durability, available in safety yellow and dark brown
  • Hand stops on top of handrails shall be included.
  • Grab rails shall meet OSHA requirements for height and clearance
  • LadderPort™ shall be mounted to building in an architect approved manner utilizing ½” steel threaded rod with back plates or other architect approved fastening system
LadderPort Ladder Receiver Optional Gate-Self Closing Gate (Can Be RetroFit)

LadderPort Ladder Receiver Optional Self-Closing Gate

Gate easily attaches to LadderPort to stop falls from roof. Easily opens when ascending the ladder to the roof. Easy installation. Includes all installation hardware. Does not penetrate wall openings. Can be retrofit.

LadderPort Ladder Receiver Suggested Options

  • Mounting Hardware (Includes Threaded Rod, Nuts, Bolts, Washers)
  • Masonry Drill Bit Kit (1 ea 5/16x12" & 9/16x18")
  • Instructional Wall Sign
  • Roof Pad (Available in Powder Coated Yellow or Brown)
  • Galvanized Roof Pad (Special Order: Allow 4-6 wks delivery)
LadderDock

HOLD YOUR EXTENSION LADDER FIRMLY IN PLACE!

Use this model when the only solid attach point is a wood nailer or other solid base supporting the roof edge flashing. This model requires the ladder to extend above the roofline. Includes mounting hardware.

  • Standard Powder Coated Brown or Safety Yellow
  • Special Order: Galvanized

"cranky" portable winch systems

Designed to easily and safely haul items, such as motors, compressors and toolboxes up to the roof. “Cranky” Portable Winch slips on and off the building’s permanently mounted Cranky Building Post, the “Port-A-Post” (for use with roof hatch or permanently mounted vertical ladders) or it on the “Cranky” Truck or Van Mount
Post. At 29 pounds, “Cranky” is easy to transport.

LIFTS ITEMS UP TO 300LBS!

“Cranky” and “Cranky” accessories allow one tech to lift heavier items from vehicle to roof without the expense of a crane or second technician. “Cranky” Portable Winch System uses a grab hook to tote items up to 300 pounds. A lift chain with S hooks is also included. “Cranky” Portable Winch is equipped with a brake to stop the
hand crank for added safety and a back pulley to center loads when hoisting through a smaller roof hatch. The crank ratio is 4.4:1.

Turning handle & boom telescope & retract for easy transport. Powder coated in safety yellow for lasting durability. Telescoping boom made of stainless steel. Equipped with hand brake for safety & back pulley for use with “Port-A-Post”. Lifting chain with “S” hooks included.

  • Collapsible, Lightweight, Portable
  • Boom Expansion 32" (approx.)
  • Handle Expansion 1' (approx.)
  • Turning handled provides easy maneuverability
  • Hand stops on top of handrails shall be included
  • Entire assembly shall be powder-coated safety yellow for lasting durability
  • Hatch kit shall include fasteners, drills, and sealant for installation
  • Handles shall be adjustable for all standard hatch widths 24″ to 48″
“Cranky” Building Mount Post Type 1*

Permanent Mounted Post for use with a flat wall when the mount is flush against the wall. Stainless steel cap protects post from the elements. Post is powder coated in brown or safety yellow. Custom colors are available for an additional charge.

Suggested Options:

  • Mounting Hardware (Includes Threaded Rod, Nuts, Bolts, Washers)
  • Masonry Drill Bit Kit (1 ea 5/16×12″ & 9/16×18″)
  • Designed for Flat Wall Application
  • Cranky mounting post shall be of schedule 80 steel pipe and shall include stainless steel top welded in place
  • Top & Bottom mounting tabs shall be securely fastened to masonry construction utilizing ½” steel threaded rod and back plates or other architect approved fastening system
  • Assembly shall be powder coated and designed to support up to a 300lb. non-human load when utilizing the Cranky personal winch system as manufactured by LadderTech, L.L.C
“Cranky” Building Mount Post Type 2*

Permanent Mounted Post for use when a gutter is present. Stainless steel cap protects post from the elements. Post is powder coated in brown or safety yellow. Custom colors are available for an additional charge.

Suggested Options:

  • Mounting Hardware (Includes Threaded Rod, Nuts, Bolts, Washers)
  • Designed to Provide Clearance for Commercial Gutters up to 8×8
  • Cranky mounting post shall be of schedule 80 steel pipe and shall include stainless steel top welded in place
  • Bottom mounting tabs shall be securely fastened to masonry construction utilizing ½” steel threaded rod and back plates or other architect approved fastening system
  • Assembly shall be powder coated and designed to support up to a 300lb. non-human load when utilizing the Cranky personal winch system as manufactured by LadderTech, L.L.C
“Cranky” Building Mount Post Type 3*

Adjustable Mount for use when decorative molding is present at the top of the wall. Top mounting must be solid attach point.

Suggested Options:

  • Mounting Hardware (Includes Threaded Rod, Nuts, Bolts, Washers)
  • Masonry Drill Bit Kit (1 ea 5/16×12″ & 9/16×18″)
  • Designed for Use with Cornice Detail
  • Shall be securely fastened to wood nailer or other suitable structural member at top of cornice
  • Shall be set with lower adjustable stand offs level to match top mount
  • Lower mounting stand offs shall be cut and drilled in accordance with included instructions for proper length to allow for level mounting.
  • Bottom mounting tabs shall be securely fastened to masonry construction utilizing ½” steel threaded rod and back plates or other architect approved fastening system
  • Assembly shall be powder coated and designed to support up to a 300lb. non-human load when utilizing the Cranky personal winch system as manufactured by LadderTech, L.L.C
Cranky Solid Mount Post

solid mount post

The Solid Mount Post is designed to mount to a secure surface,
such as a concrete floor. Prior to installing on a roof, please verify proper
installation method with an engineer or architect.

“Cranky” Hitch Assembly Post – Truck or Van Mount*
“Cranky” Hitch Assembly Post – Truck or Van Mount*

“Cranky” Hitch Assembly Post – Truck or Van Mount*

For use with “Cranky” Portable Winch to lift heavy compressors, motors or other parts off the truck/van. Simply remove “Cranky” & use with Support Post (shown above) or “Port-A-Post” to lift to the roof. Slips into standard 2” Reese Type Receivers.

"Port-a-post" portable post

For use with “Cranky” Portable Winch. Simply set “Port-A-Post” on ladder and place “Cranky” on post. Quickly & securely sets on the roof hatch ladder or other permanent vertical ladder allowing the technician to easily lift heavy objects such as compressors and motors directly through the roof hatch or up a vertical ladder. Post includes double clipped rope for toting “Port-A-Post” & “Cranky” to roof in one trip. Slips on in approximately sixty seconds.
Post is powder coated in safety yellow for lasting durability. Port-A-Post weighs approximately 35 lbs.

  • Adapter to fit round or flat rails up to 2”. Side stringer must be 5/8”
  • Fits up to 1” round or flat rails. Side stringer up to 5/8”
  • Side support bracket fits up to 5/8″ side rail
  • Sliding “u” bracket and side bracket adjustable to allow mounting to different rung heights
  • Cranky Mounting Post shall be made of schedule 80 steel pipe
  • Attachment loop for Port-A-Post lifting rope
  • Bottom welded “u” bracket cradles permanently mounted 1″ ladder rung
  • Hitch pins included to secure top and bottom “u” brackets
  • 2″ adapter available for 2″ ladder rung
  • Assembly shall be powder coated and designed to support up to a 300lb. non-human load when utilizing the Cranky personal winch system as manufactured by LadderTech, L.L.C.
Ladder Port awarded 2013 Retailer Choice for best new product
Ladder Port awarded 2016 PUPN Dean's List Award
  • Designed for Use with Any Size Roof Hatch
  • Roof Hatch Safety Grab Bar kit shall be fabricated from welded heavy gauge tubular steel construction utilizing formed steel, laser cut side rails
  • Main mounting bolts shall be stabilized by close tolerance heavy tube steel
  • Hatch handles shall be of height and distance apart to meet OSHA specifications
  • Hand stops on top of handrails shall be included
  • Entire assembly shall be powder-coated safety yellow for lasting durability
  • Hatch kit shall include fasteners, drills, and sealant for installation
  • Handles shall be adjustable for all standard hatch widths 24″ to 48″
ROOF HATCH SAFETY GRAB BARS

When you use a roof hatch, the Roof Hatch Safety Grab Bars make it much safer and more comfortable. Included drill bits and mounting hardware make the Grab Bars easy to install on your roof hatch. Constructed of heavy welded steel. Adjustable to fit all standard roof hatches 24” – 48”. The only uninterrupted grab bars with hand stops meeting OSHA Regulation 1910.27(d)(3). Powder coated in safety yellow for lasting durability.

ROOF HATCH SAFETY GRAB BARS

When you use a roof hatch, the Roof Hatch Safety Grab Bars make it much safer and more comfortable. Included drill bits and mounting hardware make the Grab Bars easy to install on your roof hatch. Constructed of heavy welded steel. Adjustable to fit all standard roof hatches 24” – 48”. The only uninterrupted grab bars with hand stops meeting OSHA Regulation 1910.27(d)(3). Powder coated in safety yellow for lasting durability.

Caged Roof Hatch Grab Bars

The Caged Roof Hatch Safety Grab bars provide an added measure of safety to your existing roof hatch. Constructed of heavy welded steel. *Fits roof hatches 30”–48” with standard adder orientation. Easy installation, will not crush insulation. Hardware included. *Larger sizes available. Must provide ladder placement & direction of hatch opening, length & width. Call for quote.

Meets Often Enforced OSHA Walking-Working Surface Regulations

Caged Roof Hatch Grab Bars* With Optional Adjustable Self Closing Gate

The Optional Adjustable Self Closing Gate is made to allow clearance for your hands when holding the only OSHA compliant uninterrupted grab bars. Easily opens even when both hands are on the grab bar and swings closed and stays closed when not in use. Fits cage sizes 30″ – 41″.

Meets Often Enforced OSHA Walking-Working Surface Regulations

Adjustable Parapet Back Ladder

Use when parapet extends above the roofline. Eliminate the need for jumping off the ladder to the roof, helping to keep technicians safe. Saves wear and tear on the roof & parapet reducing repair costs. Includes stainless steel screws.

Recommended Optional Items

Mount on one or both sides of Parapet Back Ladder System with 3 or more steps. Allows the user a secure hand hold when climbing the Back Ladder. A grab rail (similar to the LadderPort grab bar) provides an added measure of safety when at the top of the Parapet Back Ladder. Sold with additional wall mount support to keep parapet back ladder solidly on the ground.

For a cleaner, more solid installation, we recommend a joiner plate to help protect the parapet wall. If the parapet width is provided we can provide a cut to measure plate or our standard 17” plate can be field cut to size. Larger widths available by request.

Demonstration Model Shown with a Type 2 – Gutter Saver Ladder Receiver.

Parapet Back Ladder, Safety Hand Grab Rail (and support – support typically attaches to
parapet wall below steps, above shown for demo purposes)
(Typically a Parapet would not have a gutter, shown for demonstration purposes only.)

LadderPort™ Platform

The Platform solves roof access problems where there is an obstruction near the roof line or a short overhang. The Platform can be ordered in several different lengths. When a parapet is present, a separate LadderPort Parapet back ladder should be ordered with the correct number of steps to accommodate the parapet height. The same safety features of LadderPort ladder receivers are incorporated into the Platform to allow the extension ladder to be held in
place for safer roof access. Since there is no vertical ladder access from the outside of your building, the Platform deters vandals and pranksters from accessing the roof.

  • Platforms can be ordered in 38”, 48”, 58”, 68” or 78” lengths
  • Other custom lengths are available in 10” increments
  • Platforms and Back Ladders are sold separately
  • Ideal when there is no solid attach point on the wall below
LadderPort™ Platform
Instructional Wall Signs

Install With LadderPort Ladder Receiver or LadderDock

Place signs at eye level below your LadderPort or LadderDock installation. No guess work as to where ladder should go and how ladder should be used when a LadderPort or LadderDock is present. Provides both written and picture instructions to prevent incorrect usage

Roof Pad

Protect your roof from wear and tear caused by sharp tools, heavy objects and technician use.
Order several and keep them in front of your HVAC units to keep the roof safe when the covers are removed.

Non slip rubber
36”x48”x1/2”

For use with LadderPort™ Types 1-3 & “Cranky” Posts 1-3

This kit is offered for easier, safer installation of LadderPort™ Ladder Receiver & Cranky Posts Types 1-3. The threaded rod allows a solid attach point for added.

4-1/2” Threaded Rods 18” Long /Back Plates, Washers, Lock Washers, Nuts

For use with LadderPort™ Types 1-3 & “Cranky” Posts 1-3

This kit is offered for your convenience, if you don’t
already own drill bits in the sizes listed below.

16”x9/16” Masonry Drill Bit & 12”x5/16” Masonry Drill Bit